bending strength

基本解釋

• [力] 彎曲強度；[力] 抗彎強度

英漢例句

雙語例句

• Considering the system errors of gear drive and teeth synthetic flexibility, the loading point of bending strength was studied.
  考慮系統誤差和輪齒綜合柔度，對齒輪彎曲強度的計算力點進行研究。
• Superhuman mental powers, including his extraordinary sense of hearing and blazing speed-reading, are as vital to Superman as his bullet-beating velocity and steel-bending strength.
  超人的精神超能力，包括他擁有的聽覺超能力和閱讀超能力，就像他擁有的可以躲避子彈的速度和折斷鋼鐵的力量一樣至關重要。
• This paper delivered the relationships of uniaxial tensile and compressive stress with strain and bending properties, and felt-bending strength of cement mortar with polyvinyl acetate(PVAC).
  研究摻聚醋酸乙烯水泥砂漿的軸拉和軸壓應力—應變關系、抗彎性能以及長期粘結抗彎強度。

權威例句

• These include their high strength, which makes it possible to create extremely rigid structures in terms of torsion and bending, excellent crash performance and low weight.
  ENGADGET: Visualized: Mercedes-Benz SLS AMG E-Cell bares all

• bending strength更多例句

詞組短語

短語

• repeated bending stress strength 反復彎曲疲勞強度極限
• bending ultimate strength 抗彎強度
• bending tensile strength 抗彎拉強度
• bending yield strength 彎屈服強度
• bending endurance strength 彎曲疲勞強度

• bending strength更多詞組

專業釋義

機械工程

• 彎曲強度

  At high temperature, bending strength of TiC-Ni cermets decreased with temperature increasing and plastic distortion took place beyond 1000℃.
  隨著溫度的升高，TiC-Ni材料彎曲強度下降，溫度超過1000℃開始發生塑性變形。

• 抗彎強度

  Correspondingly, the wrapping materials have smaller effects on the tensile strength, and the species of the rattan cane have smaller effect on the bending strength.
  纏結材料對抗拉強度影響顯著程度相對較小,基材對抗彎強度影響顯著程度相對較小。

• 齒根應力

  On the condition of knowing the root stress value of x-zero gear, the bending strength of x-gears with the same teeth can be calculated through the formula.
  在已知標準齒輪齒根應力值的前提下，通過該計算式便可算出任一變位下的齒根最大應力。

  化學

• 抗彎強度

  The bulk density of this material is 2.71 g/cm3, the bending strength is 120MPa, the dielectric constant and the dielectric loss at 1MHz are 8.6 and 1.27×10-3 respectivly.
  燒結試樣的體積密度為2.71g/cm3,抗彎強度為120MPa;在1MHz的測試頻率下,其介電常數為8.6,介電損耗為1.27×10-3。

• 彎曲強度

  Adding of LDPE causes the melt strength to grow but the stretching and bending strength to decrease.
  低密度聚乙烯用量增加時，熔體強度會有所上升，但力學性能會下降。 總的說來，熔體強度高的產物沖擊強度較高，但拉伸強度和彎曲強度有下降的傾向。

• 抗折強度

  At the same condition,the bending strength and bulk density of sample made of retotite were better than that of sample of kaolinite.
  ③在相同條件下，以累托石質配方制備的樣品的抗折強度、體積密度大于以高嶺土質配方制備的樣品。

  能源科學技術

• 抗折強度

  Comparison of the compressive and bending strength of set cement for different formulations and curing time, the use of early-strength agent ranging from 1.2% to1.8% can significantly improve the early-strength of set cement.
  通過對不同配方和不同養護時間的水泥石抗壓、抗折強度實驗對比得到:加入早強劑可以顯著提高配方水泥石的早期強度,早強劑加量范圍為1.2~1.8%之間。

  物理學

• 撓曲強度
• 抗折強度
• 抗撓強度
• 抗屈強度

地球科學

• 抗彎曲強度

交通運輸工程

• 抗彎強度
• 彎曲強度